Crucial Warning: NEVER flash China MIUI packages built for the Xiaomi Mi CC9e (codename laurus) onto the Android One Mi A3 (laurel_sprout). Despite identical Snapdragon 665 chips, laurus uses a non-A/B partition layout with a dedicated recovery partition, whereas laurel_sprout uses a pure dual-slot A/B architecture — cross-flashing will corrupt the partition table and trigger a Qualcomm 9008 hard brick. Always verify "clean all" is checked in Mi Flash Tool.
Xiaomi Mi A3 (laurel_sprout) Android 11 Stock & TWRP Recoveries
Official Android One Stock Releases (Android 11.0) 2 packages
laurel_sprout_global_images_V12.0.26.0.RFQMIXM_20220808.0000.00_11.0_2292e2c0b1.tgz
Final official Global Android One Fastboot release for M1906F9SH (2,439,506,308 bytes). Complete factory restore for bootloops and unbricking.
MD5: 2292e2c0b1c0e9839d5b14427154b5b4
laurel_sprout_eea_global_images_V12.0.23.0.RFQEUXM_20220815.0000.00_11.0_2d87b18c16.tgz
Final official European Economic Area (EEA) Android One Fastboot image (2,332,312,751 bytes). Fully compliant with UK and European regulatory standards.
MD5: 2d87b18c16c3ade1a30384221eba165a
Custom Recoveries (Official TeamWin TWRP A/B) 4 packages
twrp-3.7.0_9-0-laurel_sprout.img
Official TeamWin bootable image (43,048,960 bytes). Boot via "fastboot boot twrp-3.7.0_9-0-laurel_sprout.img" to start a temporary recovery session or flash ZIP installers.
MD5: e5eef0bdc9e42abb4a262bb5288165c5
twrp-installer-3.7.0_9-0-laurel_sprout.zip
Official TeamWin dual-slot installer ZIP (20,619,730 bytes). Flash from within TWRP to permanently patch both boot_a and boot_b slots.
MD5: ae90c8bfe72dc0dbb6d974c280448bfc
twrp-3.6.2_9-0-laurel_sprout.img
Official TeamWin legacy boot image (43,048,960 bytes). For maintenance and flashing legacy Android 9/10 A/B custom ROMs.
MD5: e8f0a476bdd4c8620892f6ceff090d24
twrp-installer-3.6.2_9-0-laurel_sprout.zip
Official TeamWin legacy dual-slot installer ZIP (20,608,131 bytes). Injects recovery ramdisk across both slots during legacy recovery sessions.
MD5: 5e3771217fab76c2e8824268a1d95796
Fastboot, Critical Unlock & Dual-Slot A/B Overview
- Confirm board M1906F9SH reports "laurel_sprout", never China sister model "laurus"
- Extract laurel_sprout_global_images_V12.0.26.0.RFQMIXM_20220808.0000.00_11.0_2292e2c0b1.tgz twice to C:\mia3_fw\
- Reboot into Fastboot (Volume Down + Power) and run both unlock and unlock_critical commands
- Flash C:\mia3_fw\ via Mi Flash Tool ("clean all"), or fastboot boot twrp-3.7.0_9-0-laurel_sprout.img
- Confirm A/B partition writing across active slot, and visit FlashGuideHub for persist and slot guides
Hardware Board, UFS Storage & Package Verification Checks
- Run 'fastboot getvar product' in Fastboot mode to confirm the hardware codename returns 'laurel_sprout' (M1906F9SH) and NOT its China sister device 'laurus'.
- Verify downloaded archive integrity using verified MD5 checksums: laurel_sprout_global_images_V12.0.26.0.RFQMIXM_20220808.0000.00_11.0_2292e2c0b1.tgz (MD5: 2292e2c0b1c0e9839d5b14427154b5b4) and laurel_sprout_eea_global_images_V12.0.23.0.RFQEUXM_20220815.0000.00_11.0_2d87b18c16.tgz (MD5: 2d87b18c16c3ade1a30384221eba165a).
- Inspect UFS 2.1 storage stability before full wiping: ensure write operations complete without I/O timeouts, and check active slot status using 'fastboot getvar current-slot'.
- Understand that laurel_sprout lacks an independent /recovery partition: test-boot twrp-3.7.0_9-0-laurel_sprout.img via 'fastboot boot', then flash twrp-installer-3.7.0_9-0-laurel_sprout.zip inside recovery to patch both boot_a and boot_b slots.
- When flashing custom boot or recovery images, disable AVB 2.0 flags via 'fastboot --disable-verity --disable-verification flash vbmeta vbmeta.img' to avoid dm-verity boot halts.
- Charge the 4,030 mAh non-removable Li-Po battery above 40% via USB Type-C, and always plug into a native rear motherboard USB 2.0 port to prevent Qualcomm Fastboot packet drops.
- If the handset is completely unresponsive with a black screen in Qualcomm HS-USB QDLoader 9008 mode, emergency recovery requires motherboard EDL test points with the battery flex disconnected.
Android One Pure A/B (laurel_sprout) vs China MIUI CC9e (laurus)
Because the Mi A3 operates on Google Android One stock AOSP rather than MIUI, unlocking bypasses Xiaomi account binding and wait periods. Enable OEM Unlocking and run both "fastboot flashing unlock" and "fastboot flashing unlock_critical" to write low-level partitions.
Ready to Flash This Firmware?
Full step-by-step instructions for Xiaomi Mi A3 (Android One), including prerequisites, error fixes, and screenshots, are on FlashGuideHub's Mi Flash Tool guide.
Can also be flashed via Fastboot: Open Fastboot Guide →
Mi A3 Hardware Variants, Build Codes & Recovery Taxonomy Q&A
While both phones share Qualcomm's Snapdragon 665 platform and camera setup, the Mi A3 uses a pure A/B partition topology (boot_a/boot_b, system_a/system_b) without a standalone recovery partition for Google Android One updates. In contrast, the CC9e (laurus) uses a traditional A-only layout with a dedicated /recovery partition running MIUI China. Cross-flashing packages between them corrupts the GPT partition table and causes a hard brick.
In the build tag RFQMIXM, "R" signifies Android 11, "FQ" is the unique hardware identifier for laurel_sprout, and "MI" denotes the Global Android One channel. Xiaomi's V12 numbering prefix corresponds to their distribution system, yet the software inside is pure Google AOSP with zero MIUI frameworks. Because Xiaomi.eu compiles translations and mods exclusively from China MIUI ROMs, no official Xiaomi.eu release exists for laurel_sprout.
The Mi A3 upgraded internal storage from the eMMC 5.1 chips used in older Mi A models to faster dual-channel UFS 2.1 flash memory in 64 GB and 128 GB capacities, paired with 4 GB or 6 GB LPDDR4X RAM. Furthermore, Xiaomi reintroduced storage expansion via a hybrid secondary Nano-SIM/microSDXC tray accepting cards up to 256 GB, which was absent on the Mi A2.
Since laurel_sprout embeds its recovery ramdisk directly inside the boot partition rather than having a standalone /recovery partition, twrp-3.7.0_9-0-laurel_sprout.img is designed for temporary RAM booting via "fastboot boot". To make TWRP permanent, users flash twrp-installer-3.7.0_9-0-laurel_sprout.zip from within TWRP to patch both boot_a and boot_b. Flashing custom boot images also requires disabling AVB 2.0 checks by flashing vbmeta with "--disable-verity --disable-verification" flags to avoid boot verification halts.