ZTE Blade A7 (2019) Firmware Flash File Download [Stock Rom]
The ZTE Blade A7 (2019) was a highly popular budget smartphone, offering a large waterdrop-notch display and solid performance for its price point. If your device is struggling with software issues like being stuck in a bootloop, infected with malware, or has become unresponsive, flashing the official stock firmware is the most effective way to restore it to its original, functional state.
Important Note: This smartphone is powered by a UNISOC SC9863A chipset. The restoration process requires the SPD Upgrade Tool and the official firmware in .pac format. This firmware package is specifically for the European (EEA) region.
Quick Device Specs
- Device: ZTE Blade A7 (2019)
- Model: P963F02
- Release year: 2019
- Chipset: UNISOC SC9863A
- Display: 6.09″ IPS LCD, 1560×720
- Battery: 3200 mAh (Non-removable)
- Memory: 2GB/3GB RAM + 32GB/64GB storage
- Camera: 16MP rear, 5MP front
- OS: Android 9.0 (Pie)
Required Downloads
| File / Tool | Download Link |
|---|---|
| SPD Upgrade Tool | Download Tool |
| SPD/UNISOC USB Drivers | Download Drivers |
Stock ROM & Firmware
| Version | Android | Region | Type | Download | Size |
|---|---|---|---|---|---|
| V1.0.0B22 | 9.0 (Pie) | Europe (EEA) | SPD / PAC | Download | ~1.4 GB |
How to Flash Using SPD Upgrade Tool
- Install Drivers: Download and extract the SPD USB Drivers. Run the setup file to install them. On Windows 10/11, you may need to disable Driver Signature Enforcement for the drivers to work correctly.
- Extract Files: Unzip the downloaded Firmware file (…SPD.zip) to get the firmware package with a .pac extension. Also, extract the SPD Upgrade Tool to a separate folder.
- Launch the Tool: Open the SPD Upgrade Tool folder and double-click UpgradeDownload.exe to run the application.
- Load Firmware: Click the first gear icon (Load Packet). Navigate to the folder where you extracted the firmware and select the .pac file. The tool will take a few moments to load and verify it.
- Prepare the Phone: Power off your ZTE Blade A7 2019 completely.
- Begin Flashing: Click the “Play” icon (Start Downloading) in the tool. Immediately press and hold the Volume Down button on your phone and connect it to the PC via USB cable.
- Monitor the Process: The tool will detect the device and a blue progress bar will appear. You can release the volume button. Wait for the process to complete, which is indicated by a green “Passed” message.
- Reboot: Disconnect your phone and hold the Power button to turn it on. The first boot after a full flash will take longer than normal.
FAQs
Q1. Will this firmware work on a ZTE Blade A7 2020 model?
No, absolutely not. This firmware is strictly for the Blade A7 (2019) model which uses a UNISOC chipset. The Blade A7 2020 is a different phone with different hardware (often a MediaTek chipset). Flashing this firmware on the 2020 model will brick it.
Q2. Will this remove a carrier SIM lock?
No. This is a generic European stock firmware, but it will not remove a network lock placed by a specific carrier (e.g., Vodafone, Orange, TIM). The device will remain locked to its original carrier after flashing.
Q3. What does the “Checking Baudrate” error in the SPD Tool mean?
This is a very common connection error. It means the tool cannot communicate with the phone. The causes are almost always: 1) Incorrectly installed drivers. 2) A faulty USB cable or port. 3) Not holding the correct boot key (Volume Down) when connecting the phone to the PC.
Q4. What is a .pac file?
A .pac file is a compressed firmware archive used for devices with UNISOC (formerly Spreadtrum) chipsets. It contains all the phone’s software partitions (like system, boot, recovery, etc.) bundled into a single file, making it easy to flash the entire system at once using the SPD Upgrade Tool.
Troubleshooting (ZTE Blade A7 2019)
- PC does not detect the phone: This is the most frequent issue. Re-install the SPD drivers, restart your computer, try a different USB port (USB 2.0 often works best), and use a known-good USB cable.
- Flashing process fails midway: This could be due to a loose USB connection or a corrupted .pac file. Ensure the cable is secure throughout the process. If it fails again, re-download the firmware file.
- Phone stuck on ZTE logo after a successful flash: Give it at least 10-15 minutes on the first boot. If it is still stuck, you will need to perform a factory reset. Boot into recovery mode (hold Volume Up + Power from an off state) and select “Wipe data/factory reset”.
- Face Unlock is not working: A full firmware flash restores everything to factory defaults. You will need to go to Settings > Security & location and set up your face data again.
