Crucial Warning: Verify whether your device is a standard A1 or an operator A1t before flashing. While both models share the MediaTek Helio P23 motherboard, flashing the A1t firmware onto a standard A1 unit writes carrier-specific modem parameters that can interfere with mobile connectivity on other networks. Always keep 'Download Only' selected in SP Flash Tool — never choose 'Format All + Download', as erasing flash blocks wipes your unique NVRAM calibration and nulls your IMEI numbers.
Download Official OPPO A1 & A1t Stock Firmware
OPPO A1 Standard (Open Market Edition) 1 package
A1_11_A.24_1808091_7.1.1.rar
Official factory scatter archive for the open-market OPPO A1. Contains MT6763_Android_scatter.txt, preloader, boot, recovery, and system partitions.
⬇️ Download via Google DriveOPPO A1t (China Mobile Edition) 1 package
A1T_11_A.20_180420_7.1.1.rar
Official stock scatter release for the China Mobile carrier variant (A1t). Restores original operator software and factory partition layout.
⬇️ Download via Google DriveMediaTek Helio P23 Flashing Overview for OPPO A1
- Confirm your exact variant (standard A1 vs operator A1t) to ensure you pick the correct firmware file
- Install MediaTek USB VCOM drivers and the LibUSB-win32 filter driver on your Windows PC
- Extract A1_11_A.24_1808091_7.1.1.rar or A1T_11_A.20_180420_7.1.1.rar to locate MT6763_Android_scatter.txt
- Open an MTK Auth Bypass tool, click Disable Auth, and connect the powered-off phone while holding Volume Up + Volume Down
- Launch SP Flash Tool, load the scatter file, select Download Only mode, and set the matching bypassed COM port
- Click Download and wait for the green Download OK checkmark before disconnecting the USB cable
Pre-Flash Hardware Verification & Safety Steps
- Check the model stamp inside Settings > About Phone or printed on the original rear packaging to confirm whether you have an A1 or A1t.
- Install reliable 64-bit MediaTek USB VCOM and Preloader drivers on your Windows PC.
- Install LibUSB-win32 filter drivers to allow MTK Auth Bypass to hook the MediaTek USB serial port.
- Download and extract the matching firmware archive to obtain MT6763_Android_scatter.txt and the partition image binaries.
- Ensure the phone battery holds at least 50% charge so flashing does not cut out halfway through.
- Connect your phone using a verified microUSB data cable plugged directly into a rear PC motherboard port rather than an external USB hub.
- Make a backup of your personal media and documents if the phone still turns on, as a factory reflash formats user storage.
MediaTek BROM Interface & Bootloader Security Notes
Writing firmware via SP Flash Tool communicates directly over the MediaTek BootROM (BROM) interface, meaning you do not need to unlock the phone's bootloader. Because OPPO implemented SLA (Serial Link Authentication) on Helio P23 boards, you must run an MTK Auth Bypass utility to disable the handshake check before SP Flash Tool can flash partition files.
Ready to Flash This Firmware?
Full step-by-step instructions for OPPO A1, including prerequisites, error fixes, and screenshots, are on FlashGuideHub's SP Flash Tool guide.
Can also be flashed via MSM Download Tool: Open MSM Download Tool Guide →
OPPO A1 Hardware, Revisions & Firmware FAQ
Both models share the exact same physical chassis, 5.7-inch 720×1440 LCD panel, 3180 mAh battery, and MediaTek Helio P23 (MT6763T) octa-core SoC. The primary difference lies in the modem and software layer: the standard A1 is an open-market Chinese release with general network bands, whereas the A1t is tailored for China Mobile with dedicated operator modem profiles, pre-installed carrier apps, and TD-LTE network optimizations.
The OPPO A1 utilizes eMMC 5.1 internal flash storage paired with 4 GB of LPDDR3 RAM. Its MediaTek MT6763 partition table allocates dedicated blocks for preloader, boot, recovery, system, vendor, userdata, and critical radio calibration blocks including nvram and nvdata.
OPPO shipped the A1 on ColorOS 3.2 based on Android 7.1.1 Nougat in early 2018. Due to OPPO's regional software update policies for budget-tier A-series devices at the time, the manufacturer maintained the ColorOS 3.2 branch with stability and security patches rather than issuing a major platform upgrade to Android 8.0 Oreo or Android 9.0 Pie.
No. Unlike many of its contemporaries in the 2018 budget segment, the OPPO A1 omitted a physical capacitive fingerprint sensor on both the back and front. Instead, OPPO implemented software-driven AI facial recognition through the 8 MP front-facing camera as the primary biometric unlock mechanism.