Crucial Warning: Hardware Platform Demarcation Warning: While the POCO M2 shares base platform similarities with the Redmi 9 (lancelot), official stock firmware is not interchangeable. Flashing lancelot stock packages onto shiva hardware results in bootloops, camera sensor init failures, and partition table corruption. In Mi Flash Tool, always select "clean all" (flash_all.bat); never select "clean all and lock" on cross-regional or modified hardware.
Download Official POCO M2 Firmware & TWRP Recovery
Official Stock Fastboot Firmware 1 package
shiva_in_global_images_V12.5.7.0.RJRINXM_20220727.0000.00_11.0_in_ea3f195178.tgz
Official final Fastboot ROM package for POCO M2 and POCO M2 Reloaded. Clean flash via flash_all.bat.
MD5: ea3f19517889beebf9a0b312b616d853
Custom Recovery Packages 1 package
PocoM2-shiva-Unofficial-TWRP-3.4.2.zip
Unofficial TWRP recovery build for POCO M2 (shiva). Flash via fastboot recovery partition; patch boot or vbmeta to prevent stock overwrite.
MD5: 0fb9178fb6caa82fef2b6e4d13915829
POCO M2 Fastboot Flashing Steps & Overview
- Verify device codename shiva and unlock bootloader via official Mi Unlock tool.
- Decompress shiva_in_global_images_V12.5.7.0.RJRINXM_20220727.0000.00_11.0_in_ea3f195178.tgz twice using 7-Zip.
- Reboot handset into Fastboot mode by holding Volume Down and Power buttons.
- Load extracted folder in Mi Flash Tool and select clean all (flash_all.bat).
- Execute flash and keep USB connected while partitions install to eMMC storage.
Pre-Flash Hardware Checks & Driver Setup for POCO M2
- Execute "fastboot getvar product" in command prompt to confirm the bootloader returns "shiva" before writing official stock partitions.
- Check device Anti-Rollback index via "fastboot getvar anti" to prevent unpermitted downgrades below your installed Android baseline.
- Verify the 5000 mAh lithium battery holds at least 50% charge to prevent unexpected power cuts during multi-gigabyte system partition writes over eMMC 5.1 storage.
- Ensure you decompress shiva_in_global_images_V12.5.7.0.RJRINXM_20220727.0000.00_11.0_in_ea3f195178.tgz twice using 7-Zip directly to a short root directory such as C:pocom2_fw to prevent command-line path length errors.
- If flashing custom recoveries such as PocoM2-shiva-Unofficial-TWRP-3.4.2.zip, flash a disabled vbmeta image using "fastboot --disable-verity --disable-verification flash vbmeta vbmeta.img" to prevent the bootloader from dropping into a dm-verity loop or stock recovery overwrite.
MediaTek Helio G80 Platform Taxonomy & Twin Demarcation
Official Fastboot flashing requires unlocking the bootloader via Xiaomi's official Mi Unlock utility. Packages under codename shiva are built specifically for the MediaTek Helio G80 POCO M2 and POCO M2 Reloaded; never cross-flash these packages onto sibling Redmi 9 (lancelot) hardware.
Ready to Flash This Firmware?
Full step-by-step instructions for Xiaomi POCO M2 / POCO M2 Reloaded, including prerequisites, error fixes, and screenshots, are on FlashGuideHub's Mi Flash Tool guide.
Can also be flashed via Fastboot: Open Fastboot Guide →
POCO M2 Hardware Architecture & Firmware FAQ
Both smartphones are built on the MediaTek Helio G80 platform and share similar chassis dimensions and 5000 mAh battery capacities. However, they carry distinct bootloader product signatures (shiva vs lancelot) and camera hardware calibrations. Standard POCO M2 units shipped with 6GB LPDDR4X RAM, whereas base Redmi 9 models featured 3GB or 4GB configurations. Official stock MIUI Fastboot packages cannot be interchanged, as flashing lancelot stock ROMs on shiva causes partition mismatches, sensor init failures, and bootloops.
The POCO M2 Reloaded is identical to the standard POCO M2 in motherboard layout, Helio G80 processor, camera array, and internal display components, differing only in RAM configuration (4GB on Reloaded versus 6GB on the standard model). Both models share the exact same hardware codename (shiva) and use the identical official Fastboot ROM package (V12.5.7.0.RJRINXM) without requiring separate firmware builds.
Xiaomi concluded official software maintenance for the POCO M2 and POCO M2 Reloaded with MIUI 12.5 Enhanced Edition build V12.5.7.0.RJRINXM based on Android 11. Due to MediaTek Helio G80 board BSP support lifecycles and eMMC 5.1 throughput constraints, subsequent MIUI 13 and Android 12 upgrades were not ported to the shiva codename branch, making this build the definitive factory baseline for restorations.